Joogifontaan kinnitus põranda R/V teras
Kaubamärk:

Ühik: tk
Tarneaeg: 7 nädalad
Müüja: PEGU OÜ
Teie valik on tehtud – nüüd on aeg tellida ja nautida!
PEGU.ee e-poest ostmine on kiire, lihtne ja turvaline:
✔ Lisage tooted ostukorvi ja täitke tellimusandmed.
✔ Valige sobiv tarneviis ja maksemeetod.
✔ Kinnitame tellimuse ning asume kohe selle täitmisele!
Kiire tarne, mugav ostlemine ja usaldusväärne teenindus – kõik selleks, et saaksite oma uue lemmiktoote kiiresti kätte!
PEGU.ee – kvaliteet, stiil ja mugavus ühes kohas!
FP-001 Drinking fountain for foor installation made of 1mm thick stainless steel.
Supplied with a push button water bubbler.
Basin polished fnish Cover grinding fnish
* Customized height for children available. Made of Stainless Steel AISI 304 (1.4301)
Joogifontaan kinnitus seina FP-004, satiin
2-ne Valamu jalaga 1200x700, kõrgus 850mm , R/V teras
Нержавеющая большегрузная двойная мойка на ножках, 1200 x 700 x 850 мм
Характеристики
- stainless steel bulk double-sink with a sheating
- without a tap hole (could be made to order)
- possibility of fine plane regulation by the regulation screws on the supporting legs
- possibility to order inner sinks in dimensions: 400 x 300 x 200 mm/ 400 x 400 x 250 mm/ 400 x 400 x 200 mm
- available also in the length 1400 mm
- material CrNi 18/10 (AISI-304)
- brushed finish
- different dimensions could be made to order
Арт. № | 93160 |
Название | SLUN 16 |
automatic washing system for soles with rotary brushes - 230V, 50Hz
RMP 02 is a stainless steel sensor-controlled washing system with rotary brushes for wellingtons. A built-in photocell sensor reacts to the user holding the handrail. The electromagnetic valve switches on, opens the water inlet, the brushes start to rotate and the circular jet injection of the disinfecting lotion is carried out. After placing the foot with the wellington on the grid in between the rotary brushes, the sole is cleaned by means of the horizontal brush. There is a CENTRAL/STOP button on the handrail for emergency switch-off.
The washing system is intended for free standing installation on the floor. Imperfections in the floor are balanced out by four adjustable hobs. The construction of the system allows the outlet to be placed above floor level. Large pieces of dirt are collected by a sieve, which can be easily cleaned. The sieve and brush can be taken out without using a tool.
The RMP 02 washing system, with its easy maintenance, is mainly intended for operations where quick removal of mechanical dirt from wellingtons is required.
The canister with disinfecting solution is not part of the delivery.
Package contents
- body of the washing machine
- removable grid
- electronics with photocell
- rotary brush
- hand brush
- jerican holder
- priming hose
- adjustable supporting legs
- central stop button
Radius of sensor | 0,5 m |
Water inlet | G 1/2“ |
Water pressure | 0,1 – 1,0 MPa |
Outlet | G 6/4” |
Electricity protection | IP 55 |
Power supply | 230 V, 50 Hz |
Power requirement | 370 W |
Water temperature | max. 42°C |
Weight | 41 kg |
- Set up water inlet as per picture
- Set up outlet G 6/4” via effluvial cover
- Set up cable for power supply – 230 V, 50 Hz
Pissuaari mehhanism infra-red paigalduse karbiga, adaptoriga 230V/AC
SLP 02NZ
Urinal infra-red flushing unit with a mounting box and integrated power supply, 230 V AC
Characteristics
- system reacts to the user attendance in front of the urinal at a maximum distance of 0,7 m, minimum stay time in active range is 7,5 s
- water flows after the user leaves active range
- adjustable flushing time 0,5 - 15,5 s
- parameters adjustment by remote control SLD 03
- automatic hygiene flushing after 24 hours non-use
- possibility to regulate a water flow by the ball valve
Order number | 42023 |
Code | SLP 02NZ |
Supply specification
Technical information
Mounting box dimension: 140 x 140 x 75 mm
Operating voltage: 230 V AC/50 Hz
Active range: 0,6 - 0,75 m
Recommended flow pressure: 0,1 - 0,6 MPa
Rate of flow: 18 l/min (inf. data)
Water inlet: male thread G 3/4“
Water outlet: male thread G 3/4“
AFO 01.SC
drinking fountain with cooling designed to stand and to be attached to wall
AFO 01.SC is a drinking fountain with cooling designed to stand and to be attached to wall. User can select between uncooled water and water running through a flow cooler. The fountain is operated by means of two piezo-buttons – resistant solution. Facility keeper can set a time period after which the water flow automatically stops.
The product contains a flow cooler. It is not a design with cooled tank only where – after the pre-cooled amount of water is pumped out – the user has to wait for the next charge to be cooled.
Flexible design of water supply and outflow allows variable and easy connection of the drinking fountain as well as its dismounting.
ttles
Automatic drinking fountain (with a sensor) can be supplied per order.
AFO 01.S is manufactured from the stainless steel AISI 304.
Other materials (e.g. AISI 316) possible on order. For cleaning we recomnned WÜRTH detergents – material preservation (no. 0893 121 K) and material cleaning (no. 893 121 1).
Package contents
- Stainless housing with cone
- Electronics and control piezo-buttons
- Water supply and electromagnetic valves
- Flow cooler
- Flexible hose outflow
- Fixing and connecting material
dimensions | 330 x 900 x 365 mm |
water outlet | d = 40 mm |
water inlet | G 1/2" |
water pressure | 0,2 – 0,6 MPa, recommended 0,3 MPa |
power supply | 230 V, 50 Hz |
power input | 820 W |
weight | 24 kg |
- Set up water outlet d = 40 mm
- Set up water inlet G 1/2"
- Electric socket 230 V, or electric cable CYKY 3C x 1,5